<strong>How to remove and install the pressure pump of Videojet 1000 series printers？</strong>
1.How to remove the pressure pump of the Videojet 1000 series printers？ Unscrew the screw above the cover. After the removal is complete, open the box, there are two cables inside, and remove them. Break it out and you can take it off. Note: These two wires and sockets should be in one-to-one correspondence, and […]
<strong>How to install the ink core of the Videojet 1000 series inkjet printer?</strong>
Now we need to install the ink core. Before we assembled the ink core, we need to install the pipe. See if the washers fall off when installing： Washers must be there, or they will leak ink. Then we install it. The two screws on it must be tightened until the screws can not be […]
<strong>Videojet 3640 Laser machine：How to assemble</strong>
It says “TOP” on it, put a thick pipe on it and screw it. The other end of this pipe, installed in this position, is screwed. This is the exhaust, the exhaust will be installed to the bottom, and both above and below. Then install this straw, installed in this position, is also an exhaust. […]
<strong>Videojet 3340How to assemble scaffolds</strong>
Install the pillar first and screw the screws. Screw it out this way, lift it up, and screw it out again. Then install the cross arm and tighten the screws. Then there is the rotating shaft, rubber removed, this do not lose, this can be removed, if not see this is not good. Place the […]
<strong>Videojet 3340 laser machine：How to assemble</strong>
This is the display screen. This is a controller, also called the control unit. This is the laser. First, there is a connection between the controller and the monitor. This monitor is to be plugged in this position, and the cable is connected to the controller, both connected to the laser. If there is an […]
<strong>Videojet 1000 series：How to detect and deal with the problems after the long time placement of the inkjet printer</strong>
First, turn the machine on. Enter the advanced password on the date. Query the password, enter “920087” in, and click to confirm after entering the password. Note: Each password corresponds to the date of the day, and each password varies with the date. Click Select “System”; select Solenoid Test and select “OK”. Change “continuous” to […]
<strong>W620 640 Condensing line cleaning step guide</strong>
Inappropriate transportation or brutal handling may result in operational operation, downtime or accidental leakage of liquid from the printer exhaust pipe. Do not transport the inkjet machine with liquid in the ink core. resolvent: operation requirement: When the W620 and W640 Jets are operated or repaired, they should always be placed on a stable horizontal […]
<strong>W620 640 660 Cleaning steps before long storage or transportation</strong>
The W600 series inkjet printer is down for a long time or before transportation, the liquid must be removed from the ink core, otherwise, serious tilt or rough handling may cause a large amount of liquid outflow through the condensate pipe, and it is highly likely to discharge a large amount of ink from the […]
<strong>1240 1280 Mixed cylinder level problem treatment guidelines</strong>
This document describes the processing guidelines for the mixed cylinder level problems in the 1240 and 1280 models, which are divided into “low / empty” and “high mixed cylinder level”. Firstly,Mixed cylinder fluid level is low / empty Phenomenon / alarm: E15040 / E15969 mixed cylinder is not filled; E15066 / E15065 mixed cylinder is […]
<strong>1240 1280 solvent addition problem handling instructions</strong>
This document describes the treatment instructions for the solvent addition problems in the model 1240,1280, ink and solvent addition problems, which are divided into two categories: “too high ink viscosity” and “too low ink viscosity”. Investigation methods and solutions: Basic inspection: 1.Head height setting The nozzle height setting in the operation interface should be consistent […]